Skip to content

Next Dispatch: 03h45m22s

Australia's Ultimate Hobby & RC Shop.

How To: Set a Gear Mesh on an RC Vehicle

How ToUpdated Angus4 min read

A person using a screwdriver to adjust the gear mesh on an RC car motor, using a slip of paper between the pinion and spur gears.
In this article (6)

To set the gear mesh on an RC car, loosen the motor screws, feed a strip of printer paper between the pinion and spur gears, push the motor in until the gears pinch the paper, tighten the screws and wind the paper out. That leaves the small gap the gears need. Gear mesh is simply how closely the small metal pinion gear on the motor sits against the larger spur gear. Check it whenever you replace the motor, the spur or the pinion.

What you need

  • A hex driver that fits your motor screws, such as the MIP hex driver set

  • A strip of ordinary A4 printer paper. Not card, not a thin receipt.

  • Blue thread lock, such as Zap Blue medium strength, for the pinion's grub screw

This works on cars whose motor mount has slotted screw holes, so the motor can slide towards or away from the spur gear. Unplug the battery before you put your fingers near the gears.

How to check your gear mesh

Get to the gears first. On most rear-wheel-drive cars that means taking off the plastic gear cover. On 4WD models the centre diff and motor mount are usually exposed, or a few chassis screws away.

  1. Hold the pinion gear still with a finger.

  2. With your other hand, gently rock the spur gear back and forth.

You want a tiny amount of play, called backlash: a faint click as the spur moves slightly before it meets the pinion's teeth. If the spur doesn't move at all, the mesh is too tight. If it moves a lot and feels sloppy, it's too loose.

How to set your gear mesh (the paper trick)

  1. Loosen the motor mount. Back the motor screws off just enough that the motor slides with slight resistance. Don't take them out.

  2. Insert the paper. Feed the strip straight down between the pinion and the spur.

  3. Push the gears together. Press the motor firmly towards the spur so the paper is sandwiched tightly between the teeth.

  4. Tighten the screws while holding the motor in place.

  5. Remove the paper. Turn the spur slowly to wind it out. It should have zig-zag crimp marks from the teeth, but it should not be torn or pierced.

Now do the backlash test again. Then rotate the spur gear a full 360 degrees and check the mesh in a few different spots. Spur gears are rarely perfectly round, so make sure the mesh isn't too tight at the gear's highest point.

Check the gear alignment too

The pinion can slide along the motor shaft. If it sits too far in or out, only part of each tooth touches the spur, and that weakens the connection. Look down on the gears from above: the pinion should be centred across the width of the spur. If it isn't, loosen the grub screw in the side of the pinion, slide it into place and lock it down.

Metal pinion on a metal shaft means vibration will work that grub screw loose in time. Put a small drop of blue thread lock on its threads before you tighten it. It holds the screw and still lets you undo it with hand tools.

Gear mesh troubleshooting

Symptom

Likely cause

Fix

High-pitched whirring, car won't move

Stripped spur gear (mesh too loose, so only the tips of the teeth were engaged)

Replace the spur gear and set the mesh closer

Motor and ESC unusually hot, sluggish, short run time

Mesh may be too tight, so the gears bind

Reset the mesh with the paper trick

Clicking under acceleration

Damaged tooth or debris in the gears

Inspect the gears; clean or replace

Pinion keeps coming off

Loose grub screw

Realign the pinion and use blue thread lock

Changing the pinion or spur to alter speed? See RC gear ratios explained and how to make an RC car faster, then come back here and reset the mesh.

Share:
AngusHead of IT · Hobbies Direct

Frequently Asked Questions

What is gear mesh on an RC car?

Gear mesh is how closely the pinion gear on the motor sits against the spur gear it drives. Set right, there is a tiny amount of play between the teeth. Too loose and the spur gear's teeth strip; too tight and the gears bind, which heats the motor and speed controller.

Related Products

Related Posts